My washer will not agitate. I have already tried replacing the belts.
- Don Kopecky asked 6 years ago
- last active 6 years ago
My maytag washer won’t spin. It just stopped in the spin cycle and won’t go again. The light blinks.
- James Buchanan asked 6 years ago
- last active 6 years ago
Our kenmore elite front loading washer stopped working and there is no power at all on the machine.
I checked the circuit board, and the 220 power outlet which all seem to be fine.
I also unplugged the machine for over a 1/2 hour.
Still no power to the washer.
Please advise
- Fred Abernethy asked 6 years ago
- last active 6 years ago
Hello, My washer & dryer are located in the kitchen. I have no basement. I have a front load washer. the problem I’m having is when the washer drain the water drain in my kitchen sink.
- Harley Clark asked 6 years ago
- last active 6 years ago
the bake shuts off after 3 seconds
- Guest asked 6 years ago
- last active 6 years ago
The broil element was staying on. I replaced the control board and that fixed it for about 3 months. Then it started doing the same thing. The broil element would stay on. Not sure what else it could be. Could I have gotten another control board with a sticking broil element relay?
- Guest asked 6 years ago
- last active 6 years ago
Hi, I changed the ERC with a new one. Connect power to oven and clock powers up, then Loc rEF shows. Touch pad seems locked out. The ERC has a sticker on it that says important to set glass touch reference point. See mini manual for procedure. I do not have this mini manual. There is a part no. on the sticker 205c2793p001, don’t know if this is a good no. I’m not sure if this is what I have to do to get rid of the code and make the oven work properly. I have located the Tech sheet, says nothing about above procedure. Need help, Thanks Jim.
- learnnowjim asked 6 years ago
- last active 6 years ago
I am coming in behind a technician that has been working on this for the past month. He changed the door switches out, no idea what else. All 4 switches test good. Call tech support and they said according to the service manual this model should only have three switches. But all four switches are wired up. I can’t find the service manual can you send it to me. Thanks
- Guest asked 6 years ago
- last active 6 years ago
The washer needs to be rebooted to power up. and will not need to be powered up if you push the power within 30 seconds. But after one minute you need to do a reboot. That is unplugging it. Do I need to replace the main control board or the touch control board?
Bill
Neighhood appliance
Bill8321@aol.com
- Guest asked 6 years ago
- last active 6 years ago
What does it mean when the control panel display shows OF on freezer and refrigerator sides ?Samsung model # RS267TDRS
- Harley Clark asked 6 years ago
- last active 6 years ago
Can you help me reset the control panel on my Whirlpool model WDT720PADM2 series F60191133.The dishwasher start/cancel button will press bit does not rest or start. I flipped the breaker for 10 minutes and it continued to do the same thing. I set it on 1 hr delay thinking maybe it would start. It locked up and no cycle buttons, delay options, or extras like heated dry will change now. I flipped the breaker and left it off the rest of the day. Last night (about 5 hrs later) it’s still flashing at me. I used it Saturday with no problems. Sunday it started with this mess. My 4 yr old did spill water on the counter and into the floor but the dishwasher is completely under the lip of the countertop. I doubt that enough water may have gotten on it but if it did then why did the other buttons work before flipping the breaker. The dishwasher is about 2.5-3 yrs. I use it 3-4 times per week. We’ve checked the filters and the ensured that the racks were in properly.
- James Buchanan asked 6 years ago
- last active 6 years ago
The ice maker produces plenty of ice, but after about only about 4 days the unused cubes form a solid block in the bin that must be removed and melted in the sink. Why is this happening? My refrigerator is a model FRT21FD3A
- David Sutton asked 6 years ago
- last active 6 years ago
I have a Whirlpool Ice maker Fridge MODELGS5HAXKT(GGGG56SHHAXKT-01 Side by side Door (a) You can hear like the water going through but the Ice tray is not filling up when I fill up the tray it makes the Ice and empty it into the container and start refilling but the tray never have any (b) The Ice container has Ice when you press on the lever the motor works but no Ice is dispence (c) When you Press on the water lever no water is dispence What is the cause of these problems and how to trouble shoot them
- T&G Appliance Repair asked 6 years ago
- last active 6 years ago
Washer not draining or spinning, I got it into diagnostic mode and got it to drain, but still wont spin. Its reporting a 5A error. Not sure what to troubleshoot next.
- Guest asked 6 years ago
- last active 6 years ago
Our Bosch dishwasher is about 4 years old, after you run a cycle there is a lot of water remaining in the bottom, I have checked the sump it is clear of obstructions and the impellor turns free, after the cycle if you lift the float on the base, in about 2 or three seconds the pump runs and will drain it if you keep holding the float, it takes about a minute.
- Curtis Appliance Repair asked 6 years ago
- last active 6 years ago
I am having trouble repairing this stackable.
The issue is due to the washer cycle not going through all the way. Initially the error code said a lid switch fault a couple months ago. We replaced the lid switch a few months ago and worked fine, then the issue popped up again which the control board was replaced. Now the washer will go into the cycle not draining and the lid is still locked and not opening. We replaced the actuator, both the control panel board and the washer main board and lid lock. I am unsure on what else the issue could be as no error codes pop up and this will only happen intermittently.
- Guest asked 6 years ago
- last active 6 years ago
My kitchenaid kfis25xvms6 refrig/freezer went off. Lights inside are on, but the controls lights are off. Can I fix or do I need repair guy?
- Curtis Appliance Repair asked 6 years ago
- last active 6 years ago
I have an Amana fridge for 15 years now. The bottom freezer just doesn’t freeze anymore but ice blocks form at the back and at the bottom. Should I try to get it service – is it worth it? or get a new fridge?
- Curtis Appliance Repair asked 6 years ago
- last active 6 years ago
It builds up ice in the bottom of freezer drawer and when it gets 1/2” thick it starts to leak out onto the floor.
- Hall Refrigeration asked 6 years ago
- last active 6 years ago
My alarm on my viking refrigerator will not shut off. I have pushed the alarm off botton.
- Harley Clark asked 6 years ago
- last active 6 years ago
The drain motor won’t run , I cleaned the entire drain system, replaced the pump , replaced the control board ,but the pump only starts draining and then stops and won’t continue the wash cycle.
When I take out the water manually and start the machine again the pump run and it will finish the drain cycle and continue to the water cycle. When I press the reset (drain)
It seems that the pump is not strong enough to push all the water out I only hear it runing for a bit and then it will stop.
- Guest asked 6 years ago
- last active 6 years ago
The control panel is locked and showing F2 E1 and can’t find book
- Curtis Appliance Repair asked 6 years ago
- last active 6 years ago
Service Manual ?
- Guest asked 6 years ago
- last active 6 years ago
I have been having a recurring problem with the back panel inside the refrigerator section to freeze up, ice clogs the defrost drain and then water and ice build up under the vegtible drawers until water leaks into the freezer. three times in the past two years I have unplugged the refrigerator, removed all shelves and manually defrosted the refrigerator then removed the back panel to clear drain. I put it back together and then, within a few months I notice the same water build-up.
I watch your video entitled “Refrigerator Repair: Not cooling properly, freezing up back panel- Samsung. The video, even though listed as a Samsung, appears to have the identical defrosting mechanisim as my GE. the video explains how to change the Bimetal sensor, defrost heater and the ASM temp sensor. However, it does not describe how to diagnosis which part is defective.
Is there a way to put the refrigerator into a “Forced Defrost” mode? this way I could test to see if the defrost heater tube actually heats up.
Is there a way to test the various plugs where the defrost heater, bimetal, and Asm temp sensor plug into? I would like to ensure the plugs are at least getting power during the different stages of the defrost cycle. Thank you very much
- Guest asked 6 years ago
- last active 6 years ago
I have a Bosch gas range. The display/control panel stopped working. The igniters on stove work so can still cook, but can not operate the oven.
- Curtis Appliance Repair asked 6 years ago
- last active 6 years ago
Our Maytag fridge control panel shows off but when you hit any button they all light up.. water and ice option don’t work
- Don Kopecky asked 6 years ago
- last active 6 years ago
I have a Bosch gas range. The display/control panel stopped working. The igniters on stove work so can still cook, but can not operate the oven.
- Hall Refrigeration asked 6 years ago
- last active 6 years ago
Model JGS9900 gas range. Oven light will not go out. I have turned the power off for two minutes then turned power back on. This did not help.
- Patrick's Appliance Service asked 6 years ago
- last active 6 years ago
I have a gas oven and when we turn it on to bake, it won’t go on. Display shows 100 degrees and on, but is not heating. I checked the gas shut off under the stove and it is on.
- Harley Clark asked 6 years ago
- last active 6 years ago
This dishwasher as it tries to drain flashes E1
- Guest asked 6 years ago
- last active 6 years ago