0 votes
1k views

Dryer runs but there is no heat. The man that came out said he checked all the fuses and they were ok and that it was the board. He took the board out and showed me a place that he said was darker where the capacitors were “burnt out”. However, when I look the problem up on the internet, I see the problem can be fixed with a fuse. The board costs $175. at Amazon and over $300 at Whirlpool. I think the fuse costs about $10-$15. What is the problem?

0 votes
2k views

Unit was not making Ice. Ice maker was replaced with ice maker WPW10300024. Now making ice at the rate of 2 harvest in a 16 hour period(i had the customer count the cubes, 14 cubes in 16 hour period). They are also complaining that the cubes are small but i believe i can correct that with the adjustment screw on the ice maker. My question to you is: Is it making ice at the correct rate? Should it have harvested 3 times last night? Any service bulletins on slow ice production, if this rate could be considered slow? A tech sheet on the fridge and ice maker would be great also.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
1k views

Hi My microwave is working except for the sensor options. When I press “potatoes” or “sensor reheat” and “start” it flashes ERROR. I tried resetting via fuse; no luck. Time for a new microwave?

0 votes
2k views

Kitchen Aid KEMS308 Built in Combo. Microwave wont heat but seemingly works otherwise. Got F1E5 Replace Micro Inverter Error.

0 votes
2k views

I purchased a Fisher & Paykel fridge some years ago and now the handle on the fridge has broken off. The top of the handle is a hook that goes into the door and the bottom looks like it had a lug into the door that has sheared.

0 votes
1k views

I have a Maytag side by side fridge with freezer drawer on bottom . its 3 years old. Yesterday it stopped working out of the blue. The lights work but it does not have a running sound and is no longer cold. when i unplug and plug back in there is a hum and load knock at the ice maker screen and then nothing. Im assuming the compressor failed . But after 3 years ??/

0 votes
2k views

need service manual

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

We have a Samsung fridge displaying FF

0 votes
2k views

Pan under fridge is full of scummy water, should I clean it and add water and replace? its a Viking Professional 36″ refrigerator with freezer on the bottom.

0 votes
2k views

Whirlpool fridge beeping and clicking, not cold enough. Side by side model gc5shexns05.I hear a random relay clicks and the evap and condenser fans both shut off for a few seconds then come back on for 20 or 30 seconds on average, but it seems random. The relay that is clicking sounds like it’s in the plastic box to the left of the compressor when looking from the back. I unplugged it for a few minutes and it continues, but now there is also a double then single beep coming from what sounds like the same location. The fridge is warming up. The evap coils look a little icy and some frost on the back panel, but not a ton. I didn’t take the back of the freezer off, I was just looking through some slots and could see the bottom of the evap coils, so I don’t know how badly they are iced up, but they looked a little icy from what I could see.The compressor seemed to continue to run when the fans clicked off. What do you think is the problem?
Tom

0 votes
2k views

I have a Maytag side by side fridge with freezer drawer on bottom . its 3 years old. Yesterday it stopped working out of the blue. The lights work but it does not have a running sound and is no longer cold. when i unplug and plug back in there is a hum and load knock at the ice maker screen and then nothing. Im assuming the compressor failed . But after 3 years ??/

0 votes
2k views

My washer will not spin out, i have bedspread & small blanket, it git out of balance & i fixed it. i started out back on rinse \spin & it goes to 5

0 votes
1k views

No power on microwave. Found breaker tripped and it worked for a short time but now it’s out again and breaker is good. Model:JVM1740SP2SS

0 votes
1k views

Hello, I am having an issue with my GE microwave. when i enter time and press start, the microwave turns on, and the count down begins , but there is no sound that the microwave normally makes when the food is being heated..wanted to know how to fix that?

0 votes
2k views

Have a built-in electric oven. Has worked fine until this morning. When I push any of the features, Bake etc. iI get a reading on the center screen that says “Feature Not Available”. What do I do to get the oven to work again?

0 votes
2k views

My Whirlpool Oven says “stuck key”.

0 votes
2k views
0 votes
2k views

GE oven model JB680DT1BB, I cant see how to change the bake element? Where does it plug in, recently bought the house and the oven did not have a bake element, I have the part but the plugs are on the left and I do NOT see where it goes.

0 votes
6k views

I have a frigidaire double oven. I went to clean it and got an f8 error. I hit clear and the error went away but I can’t do anything with my oven. I turned off the breaker to the oven and let it sit. Turned it back on and the oven says locked, but it is not and it wont do anything

0 votes
2k views

Oven was working fine and then we noted that it was in “Preheat” mode with the temperature decreasing. Tried the following, turned off and tried bake then broil, then convection – nothing changed. Opened supply breaker and reclosed. Same “preheat”. Any suggestions before we call the repair service?

0 votes
2k views

I have a new Whirlpool double oven. We got the lower oven door off as in the instructions, but the hinges did not remain at a 45 degree angle. They popped back to a 90 degree angle, as when the door is attached and closed. I can’t get them back to the 45 degree angle to reinstall the door. When we try to install the hinge into the slot in the oven and slowly open the door toward 45 degree angle, they pop out of the slots and return to 90 degrees.

0 votes
2k views

I have a Frigidaire double oven. I went to clean it and got an f8 error. I hit clear and the error went away but I can’t do anything with my oven. I turned off the breaker to the oven and let it sit. Turned it back on and the oven says locked, but it is not and it wont do anything.

0 votes
2k views

Why does my whirlpool natural gas oven make a popping noise when it is on?

0 votes
5k views

The dishwasher start/cancel button will press bit does not rest or start. I flipped the breaker for 10 minutes and it continued to do the same thing. I set it on 1 hr delay thinking maybe it would start. It locked up and no cycle buttons, delay options, or extras like heated dry will change now. I flipped the breaker and left it off the rest of the day. Last night (about 5 hrs later) it’s still flashing at me. I used it Saturday with no problems. Sunday it started with this mess. My 4 yr old did spill water on the counter and into the floor but the dishwasher is completely under the lip of the countertop. I doubt that enough water may have gotten on it but if it did then why did the other buttons work before flipping the breaker. The dishwasher is about 2.5-3 yrs. I use it 3-4 times per week. We’ve checked the filters and the ensured that the racks were in properly.

0 votes
2k views

What does it mean when the control panel display shows OF on freezer and refrigerator sides ?Samsung model # RS267TDRS.

0 votes
2k views

My kitchen aid bottom drawer ice maker stopped making ice.

0 votes
1k views

I have a Whirlpool Ice maker Fridge MODELGS5HAXKT(GGGG56SHHAXKT-01 Side by side Door (a) You can hear like the water going through but the Ice tray is not filling up when I fill up the tray it makes the Ice and empty it into the container and start refilling but the tray never have any (b) The Ice container has Ice when you press on the lever the motor works but no Ice is dispence (c) When you Press on the water lever no water is dispence What is the cause of these problems and how to trouble shoot them

0 votes
2k views

My Cabrio whirlpool washer displays f5 e2 which we have found is something with the lid. However we have tried unblocking anything to the lid and it still isn’t running. The last time it ran it had a large load of bulky sheets. It made a large thumping noise and jumped a bit and then started displaying that same code. We have tried clearing the latch but that doesn’t seem to do anything.

0 votes
2k views

bake shuts off after 3 seconds

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
6k views

Error code in dryer mode e3a washer still works.

Showing 2011 - 2040 of 9k results