Repair Help

how to replace oven door lock motor

The 5 refrigerator LEDs went dim then the freezer LEDs quit. The tech sheet doesn’t show the dc voltage test on the aurora board. I watched the premium video on this one but it didn’t show how to test this condition. I replaced the aurora board but it didn’t help.
Is there any way to test the LEDs?
Could it be a bad splice or connection?
Is there a voltage test I can perform at the aurora board?
Is there a service manual that might help?
Have you seen this condition?
If it is a wiring issue where are the splices and connectors at?

Bosch dishwasher 5+ years old has worked fine. Now blowing circuit breaker at various points in cycle. I replaced power cord after observing cut taped over in cord and frayed wires inside. Cycle started normally, then breaker blew again after 30 min. What to do next?

My whirlpool washer won’t shut off after spin cycle. Fills and spins,fills and spins. Constantly repeating this.

Kitchenaid Superba

I have removed the tub nut and cannot lift basket out of tub. I sprayed wd40 after, removing tub, but, it is not coming apart, I have also, loosing and removed all the support assy bolts. and positioned tub on two blocks for support, with nothing supporting the transmission and Attempted to pound the shaft through the tub and the basket, its just isn’t moving. Do you have any ideas?

I killed it while I was wiping down the doors and handles. Touched too many places in the control panel.

My Samsung RF267AERS ice maker is not making ice. I’m not sure if I should replace the ice maker or the water value. I do receive water thru the dispenser on the door. Thanks

Dishwasher 2950 the panel goes black. turned off breaker and turned on. panel lit up, but sounds like its running for a few minutes then stops.

I have a built in GE microwave and all the keys and settings work on control panel but when you push start it hums but does not come on.

Fresh food section / refrigerator Is not defrosting and restricting the airflow with the giant block of snow. Ran the system through self diagnostic mode nothing came up but when I ran the sensor diagnostic out of the ten sensors it tested, sensor #7 failed.
Now here’s the issue, the whole system is a cluster of bunch of plastic parts
IS THERE A MAP OF THE TEMPETURE SENSORS so I can find #7 instead of finding all 10 and having to test manually?

(In Samsung category because wouldn’t find GE brand and unit compressor was Samsung)

Can I get the service manual for this model. I am getting a UE and LE code. I thought it was a bad strut so I replaced all 4. I did get it into dyagnostics and it went into a high speed spin with no issues but if you run a drain and spin it wil drain do a low speed spin then stop and repeat 3-4 times then the error code UE and LE come up.

The compressor, inverter board and main control board was changed. Before the unit was not cooling (compressor issue) and there was a audile beeping noise also compressor would try to start. NOW after everything has been changed out. There is a clicking noise and the fans will stop momentary and come back on. Also when that happens the temperature display in the top inside of refrigerator will dim. Like I noted, fans will stop and come back on, but the compressor will stay running until set temperature is reached. Please in any way possible. Thanks Ricky

My Maytag MVWX700XL2 washer starts before the spin cycle starts. Only error code was F9 E1. When it runs through diagnostic test, the spin works but not in normal cycle. Pumps out fine. Pulled everything apart. Cleaned inner drum and pump. No debris found, only some film and a little silt.

My maytag washer 4000 series will start spin once then the pump comes on to dump the water out and stay on . What can I do to fix that problem

My new speed queen TR3 washing machine does not have a spin only cycle. is there any way to trick it into just spinning?

My Maytag Series 3000 Washer keeps displaying error F21. I’ve cleaned the long drain behind the bottom front panel and also checked all the hoses and none of which are kinked or clogged. The washer will complete all cycles and drain like normal when empty, but will display F21 when filled with clothes. I’ve put a very small load in (2 shirts and a pair of jeans) to make sure it was draining properly and am still getting error F21. Help!

We have a Whirlpool LEB6300PW1 clothes dryer. Drum spins and air comes out the vent but with no heat. Is it worth fixing or should we buy a new one?

Washer making a loud surging rubbing noise on the spin cycle.

My Maytag MVWX700XL2 washer starts before the spin cycle starts. Only error code was F9 E1. When it runs through diagnostic test, the spin works but not in normal cycle. Pumps out fine. Pulled everything apart. Cleaned inner drum and pump. No debris found, only some film and a little silt.

My maytag washer 4000 series will start spin once then the pump comes on to dump the water out and stay on . What can I do to fix that problem. I have tried to unplug the unit to reset the board and it did not work.

Whirlpool washer doesn’t spin. Changed motor coupling and clutch.

My GE elec. dryer mod.# GFDR27OEHOWW when start button is pushed begins to time out but does not run, only single click sound is heard.already checked all three thermostats they are good.

This is not a quick fix the microwave problem is due to a bad door switch. There are three door switches on the interlock circuit and if any one of them goes bad the unit will not allow it to start. Most times when the switch goes bad it is typically the lower one that burns out or the upper one that burns out. When that happens the unit will not be allowed to start up and run. you would need to take that apart and check out all 3 switches on the interlock circuit.

My KitchenAid microwave convection oven turns on, lights up but carousel does not turn and food doesn’t cook. was working fine until i used what i thought was the timer for 60 minutes – turned out it was on for that length of time.

Our ice maker in the bottom freezer does not work. We also hear a crackling/clicking sound. We vacuumed the bottom really well but still no luck.

Frigidaire dishwasher not working. First it would not drain. Got all the water out with a shop vac and cleaned the drain. Went to test but not nothing happens. Lights come on and it switches over to washing but it’s quiet. No water to the dishwasher. Was thinking maybe float switch/relay.

I have an E24 code on my Bosch Dishwasher.

WHEN THE TEMPERATURE IS SET, IT VERY SLOW REACHING THE SET TEMPERATURE. AFTER REACHING THE SET TEMPERATURE, IT DROPS DOWN TO A LOW TEMPERATURE. SOMETIMES, ALL THE POWER SHUT DOWN, AT THE MIDDLE OF COOKING. THIS IS A DOUBLE OVEN. ALL THE POWER GET SHUT DOWN AT THE SAME TIME. IN BOTH THE UPPER AND LOWER OVEN.