Repair Help

Goes into rinse cycle then immediately to drain- does not actually go through the rinse cycle.Not getting dishes clean

I need to know how to remove and replace the dispenser control board part # DA42-00217A

upper oven wont unlock door lock can not remove side trim to get to installion screws to remove oven

The thermal fuse on heater keeps blowing, the thermostat, fuse, and thermistor have all been replaced but problem persists. We have checked and air flow is not an issue. What else can we do.

I need a tech sheet and if this sounds familiar please advise.

I was looking for a service manual for this particular unit the issue is an F3 error code and I like to see if I could compare the oven sensor resistance to a wiring diagram

Hi I was looking for a service manual for r this particular unit

I have a Maytag bravo dryer and the f01 code is showing and it wont start.

The ice maker control says “lock” and can’t get ice.

The wash motor doesn’t turn on, water is coming in,

doesn’t turn on to cook but the timer stills counts down like its cooking.

Getting error code e01 f01. Spin won’t start after sensing or maybe very short and slow spin. Did spin once very fast and only way to stop was unplug. Have unplugged for 10 minutes to try for reset and problem still there.

I have a Kenmore front loading washer, about 8 yrs old, that has had what sounds like occasional bearing noise lately during the spin cycle. Today during the final high speed spin there was a bang and the drum slowed right down. I think it broke something… could this be related to the bearings? When I turned the machine off the drum didn’t seem to have a problem rotating back & forth very slowly for a while like it usually does at the end of a spin. If it is the drum bearings is it an expensive repair? — if it is I’m wondering if I’d be better off getting a new washer.

Hi techs. This kenmore refrigerator is actually a Frigidaire. The auger will not run nor will the crushed cube selection work unless you put it in the service mode. In the service mode all dispenser functions work. I have checked the micro switches, I have checked door switches , I have checked wiring harnesses in the door checked continuity to the wiring harnes in the freezer, I have changed the main board and the U.I. Board. Customer stated that you could slam the freezer door and it would some times work which made me think a bad wiring or loose connection. In test mode voltages are normal going to the auger and crushed cube solenoid. I have checked the connections at the top of the doors as well. What am I missing. Would appreciate your advice. Thank you.

The burner and infinite switch part number is w10823734. The espy sensor harness on the old and new sensors won’t work on the new INF SWitch . or would it be simpler to use the old burner with the 12002121 INF SWITCH?

I need a wiring diagram. And any help you can give.

Above items not working. Are they connected. Circuit wise? Please help with troubleshooting. Put it into diagnostic mode and it shows up with replace filter sign on first step. When I advance it to next step, it says order filter. When I check filter, it says it’s hundred percent. It’s been a big mystery. Thank you.

After burner light up the spark ignitor continue to spark, this happen only on right front and right rear burners all others are fine.

I need the troubleshooting steps for dishwasher please.

i have customer who have Samsung induction range, and they got error E-84. keypad is not responding, i check the all control board and non of them have burning sign, i am planning to change touch pcb both side control board, i also download service manual and it says either invertor board or touch pcb board. how i can check inverter board without doing so much disassemble cook top remove. give me good plan to check

I have a gas range that was flagged by the gas company CO levels to high. I have a detector but didn’t bring it with me ( I was informed it was a gas leak and just brought my sniffer) Visual inspection showed a normal blue flame in oven .It is in a small apartment with no vent and the gas company didn’t leave any ppm #s .what should I be looking for to feel confident it’s not the oven just the size of apartment and no ventilation?

After make ice and fill bin start melting ice completely

Do you have a video on how to remove the control panel.

Water dispenser works fine. Replaced dual valve in door, power goes to valve but no water out of it to ice maker. Checked pilot valve in rear, has power to it for water dispenser, however no power going to pilot valve when ice maker tries to fill.

Customer called for service on his icemaker…. after replacing the water valve to no avail, I found that the compartment in the ceiling with the icemaker and fan assembly was around 25-28°F, which I knew was too warm for the icemaker to operate. Yet, the bottom freezer compartment is well cold enough, in the single digits (2-5°F).

The fan inside the Freezer behind the plastic grill spins against the back wall of the freezer causing a noise every time the fan comes on. It must be building up frost on it or something because it is intermittent. I dont know how to disassemble the unit and see whats going on. But it is loud and annoying.