Repair Help

Good morning.
Thank you for helping me out with this issue. Apparently, the selector knob has stopped the ability to increase and decrease the digital numbers on the screen. The stove top works fine, and the buttons to select oven temp, clear settings, cook time etc (along both sides of the selector knob) work when pressed..however when i press the “oven temp” , “cook time” ,”timer” buttons the “0:00” or “0” digits appear on the screen but as i turn the knob (clock wise) to set the temp of time the digits do not move. I need your help..do you think its the mother board behind the selector knob? by-the-way..When I press the button “Oven Func” >then select Bake..then press “Oven Temp” and “0” appears on screen..even with a value of the “0” the oven will “click” on.
Please help..any assistance is greatly appreciate it!
Sincerely,
Nelson

Hello, I just want to say I have not idea how to work on a dish washer but there is not to much to them. that being said I have a dish washer that runs and finishes but has water sitting in the bottom. I took it apart and there is nothing in the pump. when I send it in the drain only I can hear the pump running. I also checked the tube going to the drain and its not plugged. what now bad pump?

This is an Microwave/ Oven combo this unit has power and all functions are working except for the microwave is not producing heat. The microwave has lights and the turntable motor turns as it should, we are not sure what is causing these issues now.

Temp in freezer ok. Fridge stays at 28 degrees when set where it should be. Freezing food.

I need a video on how to remove the dryer tub.

The water line part number AJR56656503 is cracked inside the back of the cabinet. It is part #616G on the diagram. I would like some help on how to replace it. thanks

I put this unit into forces defrost and the compressor shuts off but the heating element never turns on. Checked continuity on the heating element and the bi metal. Both are within spec. I replaced the jazz board and it still does the exact same thing. I’m not sure if I could have gotten another bad board that does the exact same thing or am I missing something. The unit does go into forced defrost and everything shuts down as it should.

There is a lot of ice building up in the Ice room section. This problem is occurring every few weeks or so that Ice will build up again and cause the Icemaker to stop working.

I bought one of your repair videos, but it did not include what the description said. I hope you can help me; my freezer is not producing ice.
I am trying to find the tech sheet for WRS965CIAM00. I replaced the emitter/receiver boards and lights did not come on (though it passes Test 15 in diagnostics). I’d like to run a diagnostic, harvest etc. (This is a link to a tech sheet on your page – but it’s to an oven tech sheet.) Thanks!

-Replaced right side spark module twice now (CM didnt care about left side), Every time the oven is heated the whole top section gets extremely hot and spark module over heats causing sporadic clicking until it cools down an hour later
-Oven door shuts good
-Oven does NOT have a cooling fan because its a full gas range so no circuit boards to cool in back
-I put aluminum tape around spark module area directing the venting hot air away from the module housing
-I tried running the hood vent on maximum over the range to evacuate some heat, DIDNT help

I know the electric ignition one with the DSI ignition module has had a recall to install a cooling fan but this is a 13 year old range which the top of is over heating. Decently taken care of.. Any suggestions? I was thinking to run the module under the range to a cooler area but the micro switches on the valves are getting extremely hot too and brittle

Checked internals-Pretty clean
Checked heater-seemed fine
Checked both thermostats on the heater-seemed to be fine but couldnt test when they open
Everything else in the dryer seemed to be ok, the dryer element was cycling off and on throughout the cycle and i know one thermostat cut off is 115 Celsius which when it ran i did notice the dryer was about 200f inside which is on par with that thermostat but there is another thermostat with a lower rating which didnt seem to affect it. Let me know what yall think. Dont really need any diagrams just someone more experienced then me opinion.

wash motor turns of after about 15 minutes of run time…motor won’t start again on any cycle or in diagnostics. Cycle continues to end. Motor will start again after a period of time but does the same thing. 1 diagnostic code 4-3 motor not running. d/w 1 1/2 yrs old

do you have a video on removing the ice maker

Hello, I have a scratch and dent dryer that is new it only works on time dry. when you put it on normal it works but just does not flame up?

I need service diagnostic information. Any videos? Any tips on this one?

The refrigerator gasket hasn’t been closing properly for months. The interface on/off won’t respond nor the freezer/ refrigerator down pads. Where is the control board?

What does this sound like?
I need a parts breakdown and dissembling instructions. Also a service manual.

Washer runs normally until spin cycle the runs 5-8 min in spin then stops and goes back to rinse over and over any ideas ?

tech replaced control board ,sensor and damper
part#wr55x11070
part#wr55x10025
part#wr02x12861
the problem still not solve how can you help?

WB10X21659 HOW TO INSTALL

We have a customer with a top load Samsung washer which makes a grinding noise in agitation when the washer is perfectly level. It is not a mechanical (ie grearcase) problem but it is the rotor “shaking”. It will also think it is unbalanced and not spin out the clothes. The strange thing is that if you lean the washer back 2-3 inches it runs fine.

Ive seen front loads do something similar and have replaced the RPS sensor to fix the problem but it did not work here.
Seeing if samsung has and tech info for this washer.

Thanks!

This unit stopped working after a storm took the power out. I have verified that I am getting 120vac at the main board. The user interface is completely dead and unresponsive though. I have tried to put it in diagnostic mode and it does nothing. No lights at all on the user interface.

I’m not getting any power to my defrost t-stat. I know it’s the main board, but on this style with the user interface board on the side of the door, do I have to change the user interface board as well?

we need a video on how to replace the boot on this Samsung.

If no video, anything you may have to help me figure out how to break down this dryer would be greatly appreciated.

need to made go into test mode or show error codes

This washer appears to be one piece RE: the control top / front-sides. How do I remove the outer skin/frame to access the tub / seal?