Repair Help

This Bosch dishwasher ,will run an entire cycle but if the cycle is cancelled or completed then it will flash 0 then will refuse to do anything. Won’t respond to

This is a Kenmore made by samsung.
Part number is DE94-01471B.
I would like to know how to replace this part. Example, if microwave needs to be uninstalled. and how door comes off

refrigerator makes a noise in the freezer and it has a lot of ice in the back

Sir, my front load washer water , I start the cycle door locked with red light ,then water filled a splash stop. Door unlocked and locked again with no water filling and the door light on again After that wait 1 minute with error code f28. Please.advice thank

This unit is also overfilling, and tripping the breaker. Now we are shop testing.

This dishwasher is about 5 years old. It is not heating or drying the dishes but runs the cycle as normal. The next thing my tech thinks is there is a wire harness with a thermistor on it that my tech thinks could be the issue. We wanted to get some advice before we try this route.

I have changed the drain hose and pump but it still won’t drain.
Is there a check valve in the module?
Can it be the diverter motor?
I can blow air through the drain hose. The drain pump works fine.
What else could be the problem?

fresh food freezing in all sections

Ice is clumping. Freezer is at -3F. Not sure how to determine if there is a water leak or if there is a heat problem.

Niether water or ice entering the ice maker and no water coming out from the dispenser

Oven takes too long to get to temperture. The oven floor is getting very hot. I need to know if a regular bake element is under oven floor or what type of heat is it using. Broil element is good. Need service manual and schematic and user manual.

FROST IS BUILT UP IN FREEZER. THINKING DRAIN LINE FOR THIS. ICE MAKER LEAKING IS WHAT I’M NOT SURE OF.

The customer said when it’s beeping late at night. the control panel is not lit up and has a wrench Simbel also the control panel will not respond when buttons are pushed. But in the morning it’s lit up and has no wrench Simbel and the beeping stopped. also, the control panel will respond when buttons are pushed. Temp is in the freezer is 0 and 38 in the fresh food.

I am having a problem getting into machine need service manual breakdown or video of disassembly.

Washer leaking from the from door ,is a double unit

RIGHT FRONT BURNER NOT WORKING; BURNER IS DISCONTINUED BUT IF YOU ORDER SWITCH IT COMES WITH BURNER AND WIRING HARNESS. PART # W10823734. THIS IS NOT THE USUAL INFINITE SWITCH LIKE THE REST OF THE BURNERS. IT LOOKS LIKE THE ONE IN THE KIT BUT EPIC SENSOR NOT HOOKING UP. AM I DOING SOMETHING WRONG.

I NEED THE DOOR HINGES FOR THIS OVEN AND ANY INFORMATION YOU HAVE ON HOW TO CHANGE THEM AS WELL. THANKS IN ADVANCE.

all the electrodes keep ticking without turning on the knob……i changed spark module same results
i checked harness with continuity it seems ok…what could be the problem
thanks in advance

What could be the problem ?

This washer is giving several different codes.
LE
PE
OE
Nothing is in the pump or drain line / have reset and will drain but won’t spin clothes dry.
Any information you can give would be useful.

I replace fresh food evaporator fan assembly but it seems not come dont know what to check to test fan or diagnostic

Evaporator and condenser fan motors running compressor running outer loop in front of door hot off and on open door light does not come on press button on control and light comes on but than goes out I suspect board is bad need video on how to replace the board and to know if I should check anything else compressor has a inverter board and when I open door switch what should my switch read when I check for continuity I do want to replace board without first being able to access the control and check board out I dont believe this has a main control board in the back correct me if am wrong

THE UNIT WILL RUN FOR A FEW MINUTES AND THEN GIVE THE TE 3 ERROR CODE. I FIGURED IT IS A THIRMISTER. HOWEVER, I HAVE NEVER CHANGED ONE THIS UNIT THE ELECTRIC VENTLESS DRYER I AM LOOKING FOR SOME HELP ON THIS

checked elements and switches. check was good. voltage and continuity. could it be the control panel?

i NEED ANY TECH SHEETS ON THIS MACHINE, I NEED TO GET INTO DIAGNOSTIC MODE BECAUSE I HAVE A NO SPIN ISSUE.