Repair Help

My washer is completely unresponsive.

I am having issues with the panel on my Electrolux washer.

My washer is displaying error code 35 and I’m not sure what it means.

The soap dispenser is not working on my Electrolux washer.

My Electrolux washer will not fill with water.

My washer will not power on or do anything at all.

My washer is making a grinding noise.

My Whirlpool washer is making loud noises while spinning out.

My whirlpool washer will not agitate.

My washer will not spin.

Making loud noises and displaying error codes.

My washer is shaking and seems to be off balance.

My whirlpool washer is making grinding noises and also displays error codes.

My whirlpool washer is not draining water properly.

My Whirlpool washer is leaking water from the bottom.

The lid on my washer is scratched up. I am looking for some advice on how to replace it.

My whirlpool washer is not getting any water.

I cannot open the lid of my washer.

My Whirlpool washer is not filling with water.

My washer will not power on or do anything.

My washer is giving me error codes and I do not know what they mean.

How to diagnose 3 way valve. No frost is going to fresh food evaporator. Freezer is normal and freezing.

Yesterday my refrigerator completely quit working. The internal display was off, as well as the external. Only the internal lights worked. I reset the circuit breaker to see if the refrigerator would reset. Nothing. This morning the refrigerator is working – all display work and it is cooling and making ice. Why did it do this and how do I trouble shoot or repair?

My dishwasher was leaving dishes filthy and my silverware stained. I disassembled the dw to find the source (turns out it was a horrible p-trap plumbing job, corroded disposal, backup, etc.
Unfortunately, I violated my own rule of appliance repair, which is to photograph every step in the disassembly. When I went to reassemble, I followed the parts diagrams, only to discover GE either poorly represented the positioning of the parts or it completely omitted key parts. I then rented your video on installing the flood switch, but that did not describe what screw I was supposed to be using.

I’ve narrowed it down to (I hope) one or both of the following problems:
1. The screw holding the flood switch housing in place: what is it? (part number/size?) (GE has no reference at all to this screw in the parts diagrams). I wonder if I might be using the wrong screw? I don’t have extra screws and I believe every screw is in the right place. Maybe it’s too loose? How tight is it supposed to be?
2. The float stem O-ring. I cannot tell from the diagram where this o-ring is supposed to go. Right now, it is on the float stem, at the narrow part that inserts into the base of the sump manifold. I think it’s doing what it’s supposed to do, (with the exception of the leaky screw below it), but I’m unsure, because I can’t rule out that’s it’s positioned improperly without fixing the leaky screw.
3. Oh, yeah, well, there’s this too: when I was removing the electrical circuit board to replace the electrical cord, I broke off the little white tab on the connector clip for the Flood switch harness assembly. When I reassembled it, the board, I googled a lot of “electrical connector clips for circuit board,” etc. with no luck. Right now it’s taped into its proper place in the board, but wonder if that might not be helping things…

I appreciate your help!

THIS IS A GE WASHER STACK WITH THE DRYER
The washer will only fill and drain.
I tried to enter the service mode according to the tech sheet and it would not allow me. Seemed simple enough. I set the selector dial at 1 o’clock held the start and deep rinse ( is that button the FS the tech sheet is talking about?)
Then hold them for 3 seconds, then turn the dial to position 6 while holding the start and deep rinse 3 more seconds then release and NOTHING!
Am I doing something wrong?
Any suggestions
I’d like to see a service video on this one!!!

PLEASE send me all you can get on this one.