Temperature doesn't rise above 180 degrees.

See below diagnostic a error codes .

FAILURE/ERROR DISPLAY CODES
Before proceeding with any corrective action, perform the following
steps to enter the Diagnostics mode:
1. To recall last failure code, if not displayed, press the Cancel key to
place the range in an idle state.
2. Press the Cancel and Start keys in the following order:
CANCEL, CANCEL, START.
3. Verify the error code displayed on the control by observing for
longer than 1 minute. If the error returns, use the applicable
procedure listed below for the actual error code that is displayed.
FAILURE
(Leftmost
2 Clock
Digits)
ERROR
(Rightmost
2 Clock
Digits)
MESSAGE/DESCRIPTION
SUGGESTED CORRECTIVE ACTION PROCEDURE
F0
Default
E0 No failure
F1
Internal
E0
E1
E2
E3
E4
E9

PROCEDURE: Before proceeding, perform steps 1 through 3 above chart to enter the
Diagnostics mode.
A. Unplug range or disconnect power.
B. Replace the display board.
C. Plug in range or reconnect power.
FAILURE
(Leftmost
2 Clock
Digits)
ERROR
(Rightmost
2 Clock
Digits)
MESSAGE/DESCRIPTION
SUGGESTED CORRECTIVE ACTION PROCEDURE
F1
Internal
E5
E6
E7
E8

PROCEDURE: Before proceeding, perform steps 1 through 3 above chart to enter the
Diagnostics mode.
A. Unplug range or disconnect power.
B. Replace the power board.
C. Plug in range or reconnect power.
F2
Keypad
E0
E1
STUCK KEY (shorted key)
KEYPAD DISCONNECT or KEYPAD DISCONNECTED
PROCEDURE: Before proceeding, perform steps 1 through 3 above chart to enter the
Diagnostics mode.
A. Unplug range or disconnect power.
B. Check that the keypad is firmly connected.
C. Plug in range or reconnect power and observe for longer than 1 minute.
D. If error remains then go to step E.
E. Unplug range or disconnect power.
F. Replace keypad.
G. Plug in range or reconnect power and observe for longer than 1 minute.
H. If error remains then go to step I.
I. Unplug range or disconnect power.
J. Replace display board.
K. Plug in range or reconnect power.
TECH SHEET – DO NOT DISCARD PAGE 5
FOR SERVICE TECHNICIAN’S USE ONLY PART NO. 9761387
FAILURE
(Leftmost
2 Clock
Digits)
ERROR
(Rightmost
2 Clock
Digits)
MESSAGE/DESCRIPTION
SUGGESTED CORRECTIVE ACTION PROCEDURE
F3
Sensors
E0
E1
E2
E4
E5
E6
E7
MAIN SENSOR OPEN (top oven sensor opened)
MAIN SENSOR SHORT or MAIN SENSOR SHORTED
(top oven sensor shorted)
MEAT PROBE SHORTED
BOTTOM SENSOR OPEN (bottom oven sensor open)
LOWER SENSOR SHORT or BOTTOM SENSOR SHORT
(bottom oven sensor shorted)
WD SENSOR OPEN (warming drawer sensor open)
WD SENSOR SHORTED (warming drawer sensor shorted)
PROCEDURE: Before proceeding, perform steps 1 through 3 above chart on page 4 to
enter the Diagnostics mode.
A. Unplug range or disconnect power.
B. Open the back panels and make sure the indicated temperature sensor is
plugged in.
If it is not, plug it in to the connector and go to step I.
If it is plugged in, go to step C.
C. Check connector P3 on the power board. Make sure it is plugged in and
fully seated.
If it is not, make the proper connection and go to step I.
If it is already properly connected, go to step D.
D. Visually inspect the wires between P3 on the power board and the indicated
temperature sensor. Make sure the wires are not cut or pinched. If the wires
appear to be intact, unplug the P3 connector on the power board. Go to step E.
E. Measure indicated temperature sensor resistance value (measure between
appropriate P3 connector pins). For the following sensors, the resistance value
should read:
Main Oven Sensor Between 931 and 2869 Ω.
(Approx. 1080 Ω at room temp).
Lower Oven Sensor Between 931 and 2869 Ω.
(Approx. 1080 Ω at room temp).
Warm Drawer Sensor Between 1,500 and 319,000 Ω.
(Approx. 119,420 Ω at room temp).
Meat Probe Sensor Between 1,300 and 103,000 Ω.
(Approx. 59,000 Ω at room temp).
(Insert meat probe into meat probe jack located
inside the oven cavity prior to reading resistance.)
Measure any P3 connector pin to chassis. Resistance value should read “open”.
If it does not, replace sensor harness. Repeat step E.
If the indicated temperature sensor does not meet these requirements, go to
step F.
If the temperature sensor does meet the requirements, go to step I.
F. For MAIN, LOWER and WARM DRAWER sensors:
Replace appropriate temperature sensor. Repeat step E.
If the requirements are not met, replace sensor harness. Repeat step E.
If the requirements are still not met, go to step G.
For MEAT PROBE sensor:
Replace meat probe sensor. Repeat step E.