Powering off

Hello
Are you getting any error codes when the unit powers off ? .
1) Wake the washer by pressing any button.
2. Wait 5 seconds.
3. Press and HOLD the Start/Pause and Cancel buttons simultaneously.
As long as the buttons are held, the failure code will appear in the display as an E followed by two numbers, a number and a letter or two letters. The
control will beep and the Door Lock, Wash, Rinse, and Final Spin indicator lights will flash.

See the complete diagnostic sheet link below, it will walk you through the complete troubleshooting and stored error codes.

Matt Ace technician

E11 Fill time too long. Refer to test (1).
E13 Water leak in tub or air leak in air bell. Refer to test (2).
E21 Water not pumping out fast enough. Refer to test (3).
E23 Drain pump relay on control board failed or wire off pump. Replace control board or wire.
E24 Drain pump relay on control board failed or wire off pump. Replace control board or wire.
E31 Pressure sensor not communicating with control board. Refer to test (4).
E35 Pressure sensor indicates water overfill. Refer to test (5).
E36 Control board problem. Replace the control board.
E41 Control board thinks the door switch is open. Refer to test (6).
E43 Control board problem. Replace the control board.
E44 Control board problem. Replace the control board.
E45 Control board problem. Replace the control board.
E46 Control board problem. Replace the control board.
E47 Board thinks the door PTC circuit is open in spin. Refer to test (7).
E48 Board thinks the door PTC circuit is closed. Refer to test (7).
E52 Bad signal from tacho generator. Refer to test (8).
E56 High motor current. Refer to test (9).
E57 High current on inverter. Refer to test (9).
E58 High current on motor phase. Refer to test (9).
E59 No tacho signal for 3 seconds. Refer to test (10).
E5A High temperature on heat sink caused by overloading. Test first-if bad-rpl speed control brd.
E5B High temperature on heat sink. Replace the speed control board.
E5C High temperature on heat sink. Replace the speed control board.
E5D Communication problem. Refer to test (11).
E5E Communication problem. Refer to test (11).
E5F Communication problem. Refer to test (11).
E66 Heating element relay failure. Refer to test (14).
E67 Input voltage on microprocessor incorrect. Refer to test (15).
E68 Current leakage to ground on heater or fuse opened. Refer to test (14).
E71 Wash NTC failure. (Tub heater) Replace control board or wire.
E74 Wash temperature does not increase. Place NTC in correct position.
E75 Water temperature sensor circuit. Refer to test (12).
E76 NTC temperature for the cold water valve over the limits. Hot and cold water hoses switched.
E82 Console control problem. Replace the control board.
E83 Console control problem. Replace the control board.
E91 Comunnication error between UI board and control board. Check wiring.
E93 Console control problem. Replace the control board.
E94 Console control problem. Replace the control board.
E95 Communication error. Replace the control board.
E97 Console control problem. Replace the control board.
E98 Console control problem. Replace the control board.
EB1 Incoming power frequency out of limits. Refer to test (13)
EB2 Incoming line voltage above 130 VAC. Check voltage at the outlet. If below
130 VAC, replace the control board.
EB3 Incoming line voltage below 90 VAC. Check voltage at the outlet. If above
90 VAC, replace the control board.
EF1 Clogged drain pump. Unclog the drain pump.
EF2 Too much soap. Advise customer to reduce the am
EBE Console control problem. Replace the control board.
EBF Console control problem. Replace the control board.
EF5 NTC temperature for the hot water valve over the limits. Hot and cold water hoses switched.