Does anyone have the diagnostic codes or troubleshooting information for this model ?

4-6. TROUBLESHOOTING WITH ERROR CODE
31
ERROR ERROR DECISION
BASIS
CAUSE FOR ERROR
OCCURRENCE REMEDY
WATER
SUPPLY
DRAINAGE
UNBALANCE
LID
OPEN
· WATER LEVEL
dose not rise to
the set level in within
30 minutes.
NO INLET
lamp blinks
· Water is not
completely drained
within 12 minutes.
· Laundry
unbalance during
spin.
· LID is opened in
the course of
intermittent spin,
normal spin or
processing
reservation.
· Water faucet is closed?
· Water supply is interrupted.
· Inlet valve is clogged with
dirts.
· Connector has bad contact
to the inlet valve.
· RED 6-pin connector has
a bad connection at the main
board.
· Is the drain hose located
properly?
· Drain hose is folded or
clogged due to freeze or dirt.
· Defective drain pump or the
WHITE 6-pin connector to the
main board has a bad
connection.
· Laundry in the INNER TUB
is filled unevenly.
· Washer is tilted.
· Lid is opened during
intermittent spin or normal
spin?
· Lid is opened while
processing reservation?
· Check the connections to the lid
switch and at the WHITE 6-pin
connector at the main board.
·O pen water faucet.
Wait until water supply is
resumed.
· Clean or replace filter.
· Correct the connector
contact.
· Same as above.
· Drain hose properly positioned
at 0.9 ~ 1.2 m (36 ~ 48 inches)
above the floor.
· Make sure the drain hose is not
plugged with a foreign object.
· Check drain pump motor
contact. Replace the pump if
necessary.
· Load the washer as evenly as
possible.
· Adjust the leg.
· Close the lid.
· Close the lid.
· Check the connections.
· If the connection is good, check
the lead wire and replace it if
necessary.
32
ERROR ERROR DECISION
BASIS
CAUSE FOR ERROR
OCCURRENCE REMEDY
PRESSURE
SENSOR
OVER
FLOW
ERROR
MOTOR
ERROR
LID
LOCK
ERROR
· Pressure switch has a
bad connection or the
switch has failed.
· Check the connections at the
pressure switch and at the
BLUE 6-pin connector at the
main board.
· Check the pressure sensor
(21~23Ω ±10%) and
connection
· Check the valves to be sure
there is no input leakage. Then
check the drain hose and make
sure the drain pipe is between
0.9 ~ 1.2 m (36 and 48 inches)
above the floor.
· Check for blockages and leaks
in the air hose between the tub
and the pressure switch.
· Check and repair any air
leakages at the air hose
connector on the outer tub and
at any connecting parts.
· Check the connections at the hall
sensor and at the BLUE
6-pin connector on the main board.
· Check the connections at the
stator and at the yellow 3-pin or
BLUE 6-pin connector on the
main board. Test the stator to
determine it is not defective.
· Test hall sensor to determine it
is not defective.
· Turn the drum to verify the
bearings are not locked.
· Check the lid lock SW trying
locking
· Check the balance of the lid
· Reseat the connector.
· Replace the switch.
· Install the drain hose between
0.9 ~ 1.2 m (36 and 48 inches)
above the floor.
· Replace pressure sensor
switch
· Remove the foreign objects
in pressure sensor switch
air hose.
· Replace the stator if necessary.
· Replace the hall sensor if
necessary.
· Replace the bearings if
necessary.
· If trying, replace the Lid lock
SW or not trying replace the
Main PCB
· Replace the lid or se the
balance
33
ERROR ERROR DECISION
BASIS
CAUSE FOR ERROR
OCCURRENCE REMEDY
THERMISTOR
AC, MOTOR
(CLUTCH
MOTOR)
· Thermistor has a bad
connection or failed
· AC motor has a bad
connection or failed
· Clutching is failed
-. Coupling get out of
gear.
-.Coupling is broken.
· Check the connections at the
Thermistor and at the WHITE
3-pin connector at the main
board
· Test thermistor to determine it is
not detective
· Check the connections at the
AC motor and at the WHITE
6-pin connector at the main
board
· Test AC motor or coupling to
determine it is not detective
· Reseat the connector.
· Replace the thermistor if
necessary.
·Reseat the connector.
· Replace the AC motor if
necessary.
· Replace