Brand: Frigidaire

Dispenser Problem/ Repost from yesterday
Refrigerator Frigidaire
Unexpectantly the dispenser hatch rapidly opens and closes and if the dispenser is set to water it comes out each time the dispenser opens and closes. What is the cause of this problem? The customer said she googled it and found it is a common compalint. Is this so?

The main problem is NOT trickling water but that whenever the dispenser WANT’S TO; ALL ON IT’S OWN ACCORD it , at any time opens and closes its hatch over and over for several second’s then stops. Without ryme or reason. Wouldn’t this be a circuit board issue? and call for replacing it?

I replaced the dispenser module first and that didn’t help at all. Then I reinstalled the old one and replaced the main control board, and that seemed to fix it then after three trouble free days then it started again. Now what do I do? Is the display a possible cause? It is almost $500.00. Any other ways to try to determine what is the problem?

This dispenser module you sent is the one I replaced. 242100019 Sorry for the confustion. Any other suggestions

Does this question goes against my quota?

Dispenser Problem/ Repost from yesterday
Refrigerator Frigidaire
Unexpectantly the dispenser hatch rapidly opens and closes and if the dispenser is set to water it comes out each time the dispenser opens and closes. What is the cause of this problem? The customer said she googled it and found it is a common compalint. Is this so?

The main problem is NOT trickling water but that whenever the dispenser WANT’S TO; ALL ON IT’S OWN ACCORD it , at any time opens and closes its hatch over and over for several second’s then stops. Without ryme or reason. Wouldn’t this be a circuit board issue? and call for replacing it?

I replaced the dispenser module first and that didn’t help at all. Then I reinstalled the old one and replaced the main control board, and that seemed to fix it then after three trouble free days then it started again. Now what do I do? Is the display a possible cause? It is almost $500.00. Any other ways to try to determine what is the problem?

This dispenser module you sent is the one I replaced. Sorry for the confustion. Any other suggestions

ADC ADAPTIVE DEFROST BOARD PCB traces bad near orange and red wires for compressor one trace no continuity to relay on PCB board.

Unexpectantly the dispenser hatch rapidly opens and closes and if the dispenser is set to water it comes out each time the dispenser opens and closes. What is the cause of this problem? The customer said she googled it and found it is a common compalint. Is this so?

The main problem is NOT trickling water but that whenever the dispenser WANT’S TO; ALL ON IT’S OWN ACCORD it , at any time opens and closes its hatch over and over for several second’s then stops. Without ryme or reason. Wouldn’t this be a circuit board issue? and call for replacing it?

Please don’t count this as one of my four questions. I need the service manual also so I can test the functions of the dispenser and any other tests I may need

Unexpectantly the dispenser hatch rapidly opens and closes and if the dispenser is set to water it comes out each time the dispenser opens and closes. What is the cause of this problem? The customer said she googled it and found it is a common compalint. Is this so?

The main problem is not trickling water but that whenever the dispenser WANT’S TO; ALL ON IT’S OWN ACCORD it , at any time opens and closes its hatch for 10 second’s or more then stops. Without ryme or reason. Wouldn’t this be a circuit board issue? and call for replacing it?

Could that be the touch pad? dishwasher works fine at times. It is not the drain!

Burners now come on sporadically but are mostly out.

When I arrived the freezer was frosted up. I put it in the service mode in defrost and the heater did not come on. I found the defrost thermostat was open. I removed it and temporally bypassed it and still no voltage , nothing coming to the heater. is this a main board issue plus the DFTS? I need a service manuel. The tech sheet does not give much information.

I’ve checked evaporator coil for ice buildup. No ice, fan is working, freezer thermostat has continuity , freezer thermistor good, door seal in good shape and clean, no gaps, condenser is running but hot to touch, relay isn’t clicking, no unusual noises, door controller reading”high temperature” ,set on lowest setting #7 temperature is 23. Any ideas?

My customer is complaining that their refrigerator stops cooling/freezing every two weeks but after like 12 hours it will start cooling without the customer doing everything. The main control board has been changed but it happened a couple weeks after it was replaced.

Was dispensing ice from icemaker when frig went completely dark. All lights on outside including controls and the inside went out. Compressor and fans went off. Thought circuit breaker popped. Checked breaker in basement it was not tripped. Checked outlet using hair dryer (high draw) worked fine. Looked into icemaker and found a white part (thermistor maye?) with two wires wrapped around the auger and broken off with the 2 leads going back to the harness shorted together. removed the short unplugged the unit from the wall over night but has not solved the issue. Some investigation online has me suspecting the main control board. Is there any way to verify that?

Thanks

The temperatures were 17 and 45 and the control was set at the maximum. The drain is clear. When I arrived the unit was off as if the control was reading satisified when the temperatures were 17/45. All the diagnostics were passed. The complaint was that water is gathering in the drawer left hand bottom crisper. Upon inspection I saw condensation forming in that drawer on the glass shelf. All gaskets seal great. Is there a bullitin or problem with these of this nature and possibly long off times?

Hi Folks,
Keep getting error codes i20 & i30. Has anyone ever had this problem? I understand that installing Part # 5304504077 will elevate of this problem. All suggestions greatly appreciated.
Thank you,
Jan,
Barney’s Appliance

Pump motor constantly running giving error code i30 checked drain pump everything working fine

I want to know how to test the components for this problem.

the pump keeps running and im getting i30 tried resetting but i did not help

I ran the diagnostic tests on the fan and it didn’t come o n Hi or Low. Which contacts on the board will show me the 13vdc? Also the freezer door switch is not responding in the test and I checked it at the main board and got no resistance.If this switch fails will the test #15 for the evaporator fan not work? Is this the main board or the fan?

I need a service manual to test this unit. I’ve never seen this one before. Is there a way to test the temperature in the ice room? If it is turned off should the temperature be in the 40’s? I ran the checks in the tech sheet and it does move and the fill valve works but I don’t understand the principle of operation. I need to know how to disassemble it.

Does this unit use a diode for the water valves ?

I ran the diagnostic tests and started the compressor and checked the components and everything checked. Once I exited the test mode the unit restarted, compressor and fans. Could it be a bad main board?

Model # ATF6700FS1
When I press the power button the machine powers on the door locks then unlocks The lights indicate fast spin then goes to no spin then the machine powers off what could be my problem

Have a Frigidaire refrigerator that when ice is being dispensed it doesn’t stop when paddle is released.
Doesn’t stop when water is being dispensed when paddle is released…

Any suggestions?

GOOD EVENING. I SPOKE TO THE CUSTOMER AND WAS TOLD THAT THIS STARTED ABOUT SIX MONTHS AGO, BUT THEN WENT AWAY. IT STARTED AGAIN THE LAST COUPLE OF DAYS. ANY HELP WOULD BE GREAT, THANKS. TODD FROM NY.