All Answers

The issue is likely with the rotary switch. Here is the part number for the switch. WB24X25302. Below is a link to the repair video for the switch.

The issue is likely with the infinite switch. Here is the part number for the infinite switch WB24T10029. Below is the repair video for the infinite switch.

This is likely an issue with the control board. Here is the part number for the board. WB27X29093. Below is a link to the repair video for the board.

Hello
Go to page #29 in the ( Service Manual ) Go to section 4-3 Trouble diagnosis and start there. This will walk you through the diagnostics to determine what your issue is.

The issue is most likely with the door switch. Here is the part number for the switch. WB24T10147 Below is a link to the repair video.

This is most likely an issue with the door lock assembly. Here is the part number for the assembly. WB14T10092 Below is a link to the door lock assembly repair video.

Here is the part number for a replacement element. WB30X24111 Below is a link to the repair video for the element.

The issue is likely with the temperature sensor. Here is the part number for the sensor WB21X22134. Below is a link to the repair video for the sensor.

The issue could be with the broil element. Here is the part number WB44X30616. Below is a link to the repair video for the element.

The issue is most likely with the bake element. Here is the part number for the element. WB44T10060. Below is a link to the repair video for the element.

This sounds like an issue with the filter head assembly. LFX25974ST. Below is a link to the filter head assembly repair video.

This could be an issue with the evaporator cover assembly. Here is the part number AEB73944701. Below is a link to the repair video.

This sounds like an issue with the door mullion. Here is the part number for the mullion AGU73530705. Below is a link to the replacement video.

This sounds like an issue with the auger motor. Here is the part number for the motor. EAU60784228. Below is a link to the auger motor repair video.

The issue could be with the water tank. Here is the part number for the tank. AJL72911502. Below is a link for the water tank repair video.

Hello
See the video link below on how to remove cover. Then go to section 1-15 in the service manual link below to do your voltage checks . One you have done your voltage checks, go to section 3-1 for component testing to determine what component is causing your issue.

Hello
There are many possibilities for your symptom. You will need to run the unit through the load test mode on page #16 in the service manual link below. This will run run the unit through diagnostics and give you the troubleshooting recommendations on what part is needed. On pages #40 through #45 are the complete parts breakdown of this washer / dryer. I have also added a link to a washer/ dryer combo WM3488HW that has 22 videos. It is very similar to your unit.

Hello
See page #44 for proper seal installation. Here are some other possibilities for your issue.
1) Make sure you are using proper dishwasher detergent. Any other types of soap may cause sudsing inside the dishwasher, resulting in poor wash performance and possibly suds and water on your kitchen floor.It is important to use high quality detergents, such as Cascade® Platinum™ Automatic Dishwashing Detergent.
2) If the upper wash arm is cracked, it can force water to spray directly toward the dishwasher door seal, causing a leak. Remove the wash arm and inspect it for cracks. If the wash arm is cracked, replace it. These waves can cause water to leak out of the bottom of the door.
3) Sometimes food particles, soap residue, and other debris can cause clogs that prevent water from draining. A clogged drain can lead to puddling inside the dishwasher that eventually leaks out the bottom of the door.
4) Make sure the unit is properly leveled.

I recommend replacing the secondary water Inlet valve. Here is the part number for the valve. MJX41869202. Below is a link to the repair video for the valve. MJX41869202