All Answers

This sounds like an issue with the drum support roller. Here is the part number. DC97-16782A. Below is a link to the repair video.

This issue is likely being caused by a bad belt. Here is the part number for the belt. 6602-001655. Below is a link to the repair video for the belt.

The issue may be a bad pressure switch. Here is the part number for the switch. Below is a link to a repair video for the pressure switch.

The door lock likely needs to be replaced. Here is the part number. WM9000HVA. Below is a link to the repair video.

This sounds like you have a bad PCB display. Here is the part number. DC92-01999A. Below is a link to the repair video.

This sounds like an issue with the wash plate. Here is the part number. DC97-19291A. Below is a link to the repair video for the wash plate.

Hello
There are a few possibilities that could be causing your low water pressure. Shut off the saddle valve that taps in to the main water line. That will shut off the water to the refrigerator. Remove the line at the back going it to the inlet valve, put it to a 5- gallon bucket and turn on the saddle valve. Make sure you have a steady flow of water coming through the saddle valve in to the bucket. If you do not have good pressure replace the saddle valve, see video link below. If you have good water pressure out of the saddle valve. Go up to the water filter and replace it unless you have a bypass cap , the bypass cap just bypasses the filter to see if the filter is plugged. Everyone get a bypass cap when you purchase a new unit. GE # PZS22MSKEHSS Water Filter Bypass Cap . If you do not have a bypass cap replace the filter. Still no pressure after bypass cap or filter. Then replace the second valve. You have two water valves engaged to dispense water .The isolation valve and dispenser valve are both energized at same time for water to dispenser .Also there should be a mini manual at top of fridge under the hinge cover assembly with service mode error codes and for testing the water valves . You can only turn on one valve in service mode . Hope this helps Water comes into isolation valve then goes to filter head ,then to flowmeter and water valves ,then to dispenser .

The drum will likely need to be replaced. Here is the part number. DC66-00596B. Below is a link to the repair video.

The issue is likely with the water inlet valve. Here is the part number. DC62-30312J. Below is a link to the repair video for the inlet valve.

This is likely an issue with the rotor and stator. Here is the part number. DC93-00236C. below is a link to the repair video.

The issue is likely a bad PCB main. Here is the part number. DC92-02388H. Below is a link to the repair video.

The issue is likely the hot water inlet valve. Here is the part number.DC62-30314K Below is a link to the repair video.

This sounds like an issue with the water inlet valve. Here is the part number. DC97-15459G. Below is a link to the repair video.

This could be an issue with the vibration sensor. Here is the part number. DC93-00278B. Below is a link to the repair video.

This sounds like you have a bad thermistor. Here is the part number. DC90-10128N. Below is a link to the repair video.

The issue is likely a bad clutch motor. Here is the part number.DC31-00090B Below is a link to the repair video.

This sounds like an issue with the clutch assembly. Here is the part number. DC97-18439A. Below is a link to the repair video.

Hello
We have the service manual, parts breakdown and wiring schematic links below. We have the Whirlpool laundry center scheduled in June of this year for video’s.

This is likely an issue with the pressure switch. Here is the part number. 6601ER1006F. Below is a link to the repair video. https://www.appliancevideo.com/premium/lg-wm3488hw-washer-fe-error-code-pressure-switch/

This is likely an issue with the water inlet valve. Here is the part number .AJU71030102. Below is a link to the repair video.